Vinyl and aluminum siding are usually installed with galvanized roofing tacks or staples. Removing these fasteners is a matter of gentle persuasion and patience, with the goal of re-installing the siding without damage.
Once the edge of the window can be seen, the house wrap can be installed. Starting at the bottom, the first strip of house wrap is placed horizontally over the joint between the window frame and the rough opening and taped into place. Next, the second strip is installed vertically on either the left or right side either is ok and again taped into place. Lastly, a strip is installed across the top of the window and the taping process is repeated.
At this point the siding can be carefully re-installed. Your email address will not be published. We will only send you awesome stuff! Privacy Policy. Your source for the latest products and trends within the architecture, construction, interior design, and building materials industry. Facebook Youtube Pinterest. Matt Greenfield No Comments. Source: pexels. Here we will describe the common window types likely to be encountered and offer tips for how the house wrap should be applied : Wood Counterweighted Window Wood counterweighted windows were some of the first window designs that did not require hinges.
Vinyl and Aluminum Replacement Windows Both vinyl and aluminum replacement windows are designed to be installed within the existing frame of an older window. Vinyl and Aluminum New Construction Windows Adding house wrap to a home with new construction windows, whether vinyl or aluminum, is very simple. Step 1: Remove the Siding Generally speaking, most siding can be removed with a combination of nail pullers, hammers, and pry bars.
Step 3: Install the House Wrap Starting at the bottom, the first strip of house wrap is placed horizontally over the joint between the window frame and the rough opening and taped into place. Leave a Reply Cancel reply Your email address will not be published. Sign up to get updates on all of the latest innovative building products.
Get Daily Tips. Reply to George E. Edwin Pawlowski Contact options for registered users. Reply to Edwin Pawlowski. Reply to buffalobill. Art Contact options for registered users. For taping the tyvek, pella makes great tape available at Lowes or Home depot I forget which one but look for the display of Pella windows and they should have the tape. Also visit pella site and download instructions on installing their doors or windows. That should give you a good idea of what you are trying to accomplish.
Reply to Art. Tips and Warnings. Things You'll Need. Related Articles. Article Summary. Method 1. Building codes and material manufacturers recommend adjustments when installing Tyvek under certain materials, for maximum air and water barrier effectiveness.
Consider these tips if you plan to use these materials over the Tyvek, as they affect your construction plans or the amount of Tyvek you need to buy: Stucco and stone veneer do best with two layers of Tyvek. Brick and foam sheathing should have an air space between it and the Tyvek. Other materials may be installed as usual, although measures that reduce moisture in contact with the Tyvek are always recommended.
Purchase the correct Tyvek product. Tyvek HomeWrap is suitable for most residential houses. Tyvek ThermaWrap will also help maintain desirable indoor temperatures, while Tyvek DrainWrap includes vertical grooves for increased drainage when high moisture is expected. If you are constructing a commercial building, or a building more than four stories tall, consult an experienced construction expert or DuPont representative for information on more specialized products, such as Tyvek Fluid or high-performance Tyvek.
Purchasing Tyvek tape as well is recommended to help seal your wall more effectively, as described below. You may be able to purchase your Tyvek with stud marks printed on the surface at a specified width, which will make it easier to line up with your wall. Position the Tyvek. Begin by placing an edge of Tyvek at one end of the wall, leaving a 6—12 inch 15—30 cm overlap over the corner. If stud marks are printed on your Tyvek product, line them up with the first stud of your wall. The first roll should be plumb with the bottom edge of the wall.
If the wall has not yet been raised, let the Tyvek overhang the bottom edge of the wall and fasten it there with Tyvek tape or sealant.
Unroll and attach the Tyvek. Unroll so the Tyvek is taut, but not so much that it gets stretch marks or tears when fastened. Have a second person secure the Tyvek with a fastener every 6—18 inches cm , over the wall studs. Once the whole roll is attached, use cladding fasteners to attach it permanently.
Over wood, gypsum board, and most other wall materials, use large head or washer head nails. Unless installing over foam sheathing, you may use staples with at least 1 in. Cover doors and windows. Ideally, install Tyvek before installing the doors, windows, or window flashing. However, no matter what stage of construction these areas have reached, you may cover them completely with the Tyvek while first installing.
You will make adjustments to these areas once the wall is covered as described below. Overlap additional rolls of Tyvek to cover the whole wall. If the wall is higher than the width of the Tyvek roll, unroll additional Tyvek higher than the first, moving upward. Overlap the Tyvek rolls by at least 6 inches 30 cm. Make sure to cover the entire wall surface thoroughly, or air and water protection could be significantly reduced.
Use portable scaffolding, not a ladder, when covering Tyvek over high areas. Tyvek rolls are slippery and large, so secure footing is highly recommended when handling them. Cut off excess Tyvek. Use a sharp box cutter or utility knife to remove excess Tyvek from around the wall.
Make sure to fasten the Tyvek in place at the end of the wall before cutting, including along unusually shaped areas of the wall such as gables. Cut out windows in an X shape. Cut a large X from one corner diagonally from one corner to the other. Now fold the flaps to the inside and tack them down. If window flashing or a window apron has already been installed, instead cut out the entire outline of the window. Take care not to cut into the flashing itself, if it has been constructed out of a flexible material.
Cut out doors in a capital i shape. Cut an opening for the doors shaped like a capital "i," including the top and bottom horizontal bars of the letter. Cut from the corners of the door openings to each corner of the "I," with the top and bottom of the "I" located approximately 8 inches Once the cut has been made, fold the Tyvek over the door openings and tack it down on the inside of the framing.
Seal the wall wherever necessary. Use Tyvek tape or a sealant product vetted for Tyvek to cover any areas that require additional protection, forming an airtight seal. Be sure to apply tape or sealant to the following areas: The entire outline window openings except the sill base. Vertical and horizontal seams where Tyvek rolls overlap. Any tears, puncture marks, or other damage the Tyvek suffered during installation.
Larger holes may need a small piece of Tyvek wrap taped over them. Method 2.
0コメント